排序方式: 共有30条查询结果,搜索用时 31 毫秒
21.
22.
Magnesium (Mg) alloys have broad application prospects in the fields of aerospace, national defense, and military industries, owing to their advantages of high specific strength and stiffness, good damping properties, and excellent castabilities. However, defects such as oxidation inclusions, shrinkage cavities and porosities, and hot cracks are readily generated in Mg alloy components, which seriously reduce the performance stability of the products. Related repair welding technologies for Mg alloys can greatly reduce the rejection rate and production cost, and exhibit significant value in scientific research and engineering application. In this review, the weldability of Mg alloys is introduced firstly according to their physical and chemical properties. Then, various repair welding technologies and pre-weld treatments applicable to Mg alloys are systematically summarized, and the effects of welding parameters as well as heat treatments on the microstructure and performance of the repaired joints are clarified. Finally, the existing problems and development trends of repair welding technologies for Mg alloys are summarized based on the actual engineering application requirements. 相似文献
23.
飞机滚转运动的控制余度与重构效能 总被引:1,自引:0,他引:1
论证了独立操纵的左右平尾使飞机滚动运动具有较大的控制余度,它增加了飞机正常飞行时的滚转力矩,在飞行中副翼出故障时可进行补偿重构,从而提高了滚动通道的余度等级和飞行的安全性,为减少滚转通道的余度配置提供了依据,通过针对操纵面失效和卡死两类故障的重构设计和仿真也证实了上述结论,同时,初步比较说明了自修复飞控系统在上述故障下的任务可靠性和基本可靠性均高于传统控制系统。 相似文献
24.
针对姿态误差对天文观测角度量测的影响,提出结合天文观测角度量测的机载惯性/天文深度组合算法.在位置误差小角度关系分析的基础上,进一步分析惯导姿态误差引入的计算地理水平坐标系与当地地理坐标系之间的姿态误差小角度关系,推导并建立基于天文高度角和方位角量测的深组合惯性/天文量测方程,针对天文观测量测对高度通道不可观,增加气压高度为量测量,设计相应组合滤波方法.该方法充分考虑了姿态误差对于天文观测的影响,仿真验证表明所设计方案可以有效消除惯导系统陀螺累积误差,提高惯导系统的姿态精度,验证了其可行性. 相似文献
25.
26.
27.
28.
29.
异物夹杂类缺陷是搅拌摩擦焊接过程中一类典型缺陷。一旦发生该类缺陷,只有对焊缝进行挖排来去除异物后,才能实施补焊。针对挖排造成焊缝材料缺失,现有的方法是通过熔焊或赛填固体颗粒来进行填充。上述方法不仅会在焊缝中引入有异于母材的材料,而且工艺过程繁琐。特别是熔焊的焊接热会对补焊区域周围的母材造成影响,从而造成补焊接头强度的削弱。针对现有补焊方法的不足,本文提出一种双道偏置补焊方法,实施过程简便,可实现等强度补焊。经试验证明,该方法可获得与原始焊缝具有相等强度的补焊焊缝。 相似文献
30.
针对飞机壁板类零件采用修配法装配过程中需要精确获取修配加工路径的问题,提出一种基于实测点云数据的壁板类零件修配加工路径计算方法。首先设计一种基于法线差的特征点检测算法提取参考壁板的初始特征点。然后建立迭代收缩优化模型对初始特征点进行收缩优化,得到参考壁板的准确特征点。最后根据工装定位孔特征进行配准,将参考壁板的特征点映射到待修配壁板上,并将映射后的特征点按照一定顺序进行连接,得到待修配壁板的修配加工路径,按照修配路径进行加工,获得壁板装配配合边界。实验表明,该方法能够精确提取待修配壁板修配加工路径,并且经过加工验证,壁板试验件对缝间隙获得小于1.2 mm的实际效果。 相似文献